| Base parameters |  | 
| Measuring medium | Liquid or gas (compatible with contact material) | 
| Measuring range | -100kPa~0~60MPa (see range selection table for details) Range
range< 10kPa (non-conductor, non-corrosive, non-explosive gas
and humidity ≤90%RH, no condensation) | 
| Type of pressure | Gauge pressure, absolute pressure, negative pressure | 
| Temperature compensation | Standard (temperature compensation -10-70°C) 0.25%FS, 0.5%FS Optional (temperature compensation -40-80°C) 0.1%FS, 0.25%FS (Note) Note: The range range is ≤ 10kPa, and the temperature compensation
range is -10~70°C | 
| Accuracy class | 0.1%FS,0.25%FS,0.5%FS | 
| Response frequency | 5Hz,30Hz,100Hz | 
| Stable performance | ± 0.1% FS/year | 
| Temperature drift | ±0.01%FS/°C (temperature compensation range) ±0.05%FS/°C (outside
temperature compensation range) | 
| Overall weight | ≈ 450g (including 5m cable) | 
| Degree of protection | IP67 Note: The above protection level refers to the electrical
connection achieved after it is complete, and also depends on the
electrical connection plug. | 
| Output power |  | 
| Output signal | 4~20mA,RS485,0~10VDC,0~5VDC,1~5VDC,0.5~2.5VDC | 
| Power supply range | 9~36VDC,15~36VDC,3~5VDC | 
| Power range |  | 
| Current type | ≤0.02Us(W) | 
| Voltage type | ≤0.008Us(W),≤0.001Us(W) | 
| Digital | ≤0.015Us(W) | 
| Load characteristics |  | 
| Voltage type | ≥10kΩ | 
| Current type | Current load≤ {(Us-7.5)÷0.02(Us=supply voltage)}Ω | 
| Environmental conditions |  | 
| Media temperature | -40~85℃ | 
| Ambient temperature | -40~85℃ | 
| Ambient humidity | 0%~95%RH(no condensation, no condensation) | 
| Overload capacity |  | 
| Overload pressure | 300%FS,200%FS,150%FS,12kPa,50kPa,300kPa,480kPa,750kPa,800kPa,1.2MPa,2MPa,3MPa,5MPa | 
| Burst pressure | 600%FS,500%FS,400%FS,300%FS,20kPa,200kPa,600kPa,900kPa,1.25MPa,2MPa,3MPa,5MPa,9MPa,12.5MPa | 
| Overall material |  | 
| diaphragm | 316L stainless steel (contact with the medium to be measured) | 
| Process connection | 304 stainless steel (contact with the medium to be measured) | 
| enclosure | 304 stainless steel | 
| Seals | Nitrile rubber (contact) fluoroelastomer (seen pressure and
blasting chart (contact with the medium to be measured) | 
| Cable | Direct lead Measuring range≤ 1.6MPa φ7.2mm polyurethane
air-shielded cable (UV protection) Direct lead, aviation lead
Range> 1.6MPa or absolute pressure (A) φ5mm polyurethane
shielded cable (UV protection) | 
| Mechanical stability |  | 
| Seismic performance | 10g(20… 2000Hz) conforms to IEC60068-2-6 standard | 
| Impact resistance: | 500g/ms conforms to IEC60068-2-27 standard | 
| Electrical protection |  | 
| Short-circuit protection | perpetual | 
| Anti-polarity protection | No damage, but not working | 
| Insulation resistance | ≥100MΩ500VDC | 
| Dielectric strength: | 500VAC | 
| Output limits |  | 
| The output is minimal | 4mA, 0, 0.001VDC, 0.05VDC (Others: 3.8mA) | 
| Output maximum | 20mA, 2000, 10VDC, 5VDC (Others: 26mA, 12VDC) |