KLD802 Radar Level Sensor With Non Contact PTFE Lens Antenna For Continuous Level Measurement

KLD802 Radar Level Sensor With Non Contact PTFE Lens Antenna For Continuous Level Measurement

Introduction

The KLD802 Radar Level Sensor is a highly advanced device. It features a non-contact PTFE lens antenna, which is a key component for its outstanding performance. This antenna design allows for continuous level measurement without the need for physical contact with the measured substance. It is especially suitable for a wide range of applications where accuracy and reliability are essential. The sensor utilizes radar technology to emit electromagnetic waves and then analyzes the reflected signals to precisely determine the level of liquids or solids. With its durable construction and precise measurement capabilities, it can effectively operate in various industrial environments, providing accurate and real-time level data for efficient process control and inventory management.

Feature

1. Non-contact measurement.
The measurement will not be affected by changes in medium properties or process conditions, such as temperature, pressure or dust intensity. Adjusting settings is easy, eliminating the need for filling and emptying containers, saving time during instrument start-up, and making the instrument virtually maintenance-free.

2. Large measuring range and small blind area
The measurement range is 0.1~120m, which basically meets the measurement requirements of on-site working conditions.

3. The antenna size is small, the beam angle is small, and the focusing ability is strong
It is convenient for radar on-site installation. It has stronger anti-interference ability for the environment inside the tank. For example, there are stirring, heating coils, baffles, etc. in the tank or the measurement effect in the straight pipe is still good.

4. High precision
The accuracy can reach ±2mm, which can fully meet the accuracy requirements of non-metering field working conditions.

5. The signal wavelength is short
It is better for the measurement of the level of powder, particles and so on.

Product Dimension
Unit in mm:




Installation Method
Flange installation
When using flange installation, the minimum distance between the instrument and the tank
wall should be 200mm.
① datum plane
② vessel center or axis of symmetry


Hoisting Installation


Radar level sensors can measure liquids, slurries and solids. The radar level sensors has pressure and temperature resistance, and will not be affected by the measurement medium during measurement, and has high measurement accuracy. In terms of installation, if it can be used and installed correctly, it will have a good measurement effect and ensure accurate data.
For the installation of radar level sensor, we should pay attention to two points:
One is to ensure the vertical incident material level after aiming at the target material level, and the other is to avoid false echoes.So when installing, we suggest:

1. The radar level gauge should be installed at least 20CM away from the container wall, preferably about 1/6 of the container diameter. Do not install the radar level gauge above the water inlet pipe and in the center of the container, otherwise there will be many false echoes, which will interfere with normal signal reception.
2. If the radar level gauge cannot maintain an appropriate distance from the container wall due to the relatively small diameter of the container or other reasons, false echoes will appear on the container wall and the radar level gauge when the distance is small, so the debugging It is necessary to store false echoes in order to avoid errors in the future.
3. If the installation container is concave or conical, you need to pay attention to the installation. When using it, the radar beam of the radar level gauge reaches the lowest point of the bottom of the tank. If the liquid level is lower than this point, it cannot be measured. The purpose of adjusting the lowest point is to ensure the accuracy of the measurement data.


​

Xi'an Kacise Optronics Co.,Ltd. is a professional manufacturer of  measuring instruments , located in China xi’an City. Since 2008, Xi'an Kacise focused on the development and production of pressure, level and flow measuring instruments .

We have been specializing in manufacturing pressure, level and flow measuring instruments and related products for 10 years. Based on experienced technical and management personnel, through efforts of our entire staff, we have become a professional measuring instrument manufacturer and solution provider. And we are continuously trying to improve product quality.

Xi'an Kacise is qualified with ISO 9001-2008, GJB 9001B-2009, CE, intrinsic safety explosion-proof and isolated safety explosion-proof certificates, etc. which ensure that our products comply with international standards.

Kacise sensors have already been exported to America, Spain, Australia, Chile and 20 other countries and regions, and received many favorable feedbacks. Our overseas distributers are also increasing. We regard “reasonable prices, efficient production time and good after-sales service” as our tenet, and hope to cooperate with more customers for mutual development.

Our goal is simple: to sell the best products at the best prices, and provides industry-leading customer service. We personally get to know each of our customers, and we know how to discover the most valuable part of our business , to help others achieve their goals.