Vcads Truck Diagnostic Scanner Full Set
vcads 88890180 interface with PTT 1.12 /88890020 vcads pro 2.4 in
development model Set includes: Interface 88890020; USB cable; 88890027 8 Pin Cable; VCADS 2.40 /PTT 1.12 Software DVD CF30 or E6420 Laptop ( software installed well and you could use
directly)
Languages: english, cesky, dansk, Deutch, Espalol, Francis,
Italiano, Magyar, Nederlands, Polski, Portuges, Romana, Srpski,
Svenska, Turkce, Russian, Lietuva
Support Brand : All Bus, truck, construction vcads 2.40 , 88890180 interface with PTT 1.12 /88890020 The 88890180 communication unit enables PC to vehicle
communication. The device connects to the PC via a USB cable or by
wireless LAN using the 802.11 b/g standard. Operating temperature range: -40 to +85°C (-40 to +185°F). Storage temperature range: -40 to +125°C (-40 to 257°F). Before the 88890020 communication unit can be used, a driver must
be installed on the PC. In addition, a utility application
(Admin0020) can be used to check the status of the device and
update the firmware if and when needed. There are three different ways, described below, of connecting
communication unit88890180. Via USB-cable Connect the communication unit to the vehicle. Connect the USB-cable between the communication unit and the PC. Select communication unit 88890020 and USB-cable setting in window
Alternative. Directly to the communication unit Connect the communication unit to the vehicle. Select communication unit 88890020 and Direct to communication unit
in window Alternative. Security level Directly to the communication unit Communication is performed using 128 bit WEP, Wired Equivalent
Privacy. The WEP-key is generated automatically and is not seen
during the configuration. Via an access point Note: Contact the local IT-support or network technician before
installation. Connect the communication unit to the vehicle. Select communication unit 88890020 and Via an access point in
window Alternative. Security level Via an access point There are three alternatives for this: WEP and MAC-address. Communication is performed using 128 bit WEP,
Wired Equivalent Privacy. The WEP-key is written in during
configuration. The MAC-address is to be written into the access
point for additional security. WPA and PSK. Communication is performed via WPA, Wi-Fi Protected
Access. 802.1x. Communication is performed using standard EAP_MSCHAP v2.
The communication unit is then treated as a PC and will be logged
on to the network using a username and password. Product for communication unit 88890020 Communication unit 88890020 has a number of different coloured
LEDs. These LEDs show the status of the communication unit and
indicate warnings, etc. 88890180 Communication Unit with protective cover The Communication Unit 88890180 (previous parts number 88890180) is
used to enable communication between a computer and a
vehicle/machine. The Communication Unit 88890180 includes a protective cover that
encloses the wire connections and reduce situations where the unit
loose connection with the vehicle For detailed information regarding the Communication Unit ,
connection types , installation , LED’s , fault tracing and
software update , see the Tech Tool help. Warranty The Communication Unit has a 12 months warranty from delivery date.
Please note the date when you received this product . This
information is requires if the device needs to be replaced during
the warranty . How to send feedback Please use your normal channels to report feedback and problems
concerning the communication unit . Connection types There are three different ways of connecting the communication unit
; via USB cable . directly to the communication unit (wireless)or
via access point (wireless) .The default connection type for the
communication unit is via USB cable . Update software (so called Firmware) The Communication Unit includes software (so called firmware) that
is updated on a regular basis . The updates are installed with Tech
Tool DVD or in the network releases , and then needs to be
downloaded to the Communication Unit through the Update software
function . The Communication Unit must be connected both to a
computer and a vehicle during the update . RP1210 application support The Communication Unit support the RP1210 . Other applications can
use this device and perform vehicle/machine communication . The
WLAN settings needs to be configured in the Tech Tool settings
before you start your RP1210 application . The configurations ,
IP-addresses etc. are stored in an INI-file which can be used by
other RP1210 applications . There is an off-line configuration
application available on request ( only available in English). Known problems The installation procedure of the USb-driver for the communication
unit will be performed the first time the unit is connected to a
USB-port . This procedure will be repeated if the unit is connected
to another USB-port on the same computer.
Checklist before returning a faulty product: Check that all the LED sensors light up shortly when powering up
the unit. When connected only to USB: The unit should flash the LED sensors
and then light the “power USB/Communication”-LED. If the “power USB/Communication”-LED does not light up: 1. Try another USB-port 2. Check if windows performs “Installing device driver software” 3. Check the USB cable and try a different cable , or try another
PC 4. If still no function, return the communication unit When connected only to vehicle : The unit should flash the LED
sensors and then light the “Power Vehicle”-LED . If nothing light up: 1. Try replacing the vehicle cable. 2. Check that ignition is on , or try another vehicle. If the “Critical Error” –LED is lit : 1. try to update the software . 2. If still no function , return the unit . WLAN dose not work. Consult your local IT support for advanced checking of WLAN. |